DENIOS INC
1152 Industrial Blvd.1
Louisville
KY 40219

Tel.: +1 502 9337272
Email: info1@denios-us.com
Internet: www.denios-us.com

The right lighting in workplaces

Proper lighting in the workplace is crucial not only for health and well-being but also for safety.

Does your workplace have the right lighting conditions? In our FAQ, we provide some helpful tips to ensure you do not fumble in the dark about workplace lighting!

What are the risks of incorrect lighting in the workplace?

Inadequate lighting significantly increases the risk of accidents. In poor visibility, concentration, and performance can also be reduced. Physical discomfort, such as burning eyes or headaches, not only affects well-being but also has a negative impact on the frequency of errors in the work process.

Caution: Lighting too bright can also lead to problems when unsuitable or misaligned lights blind employees.

Our infographic gives you a quick overview of the adverse effects of wrong lighting in the workplace:

Who is responsible for lighting in the workplace?

The employer is expected to set up workplaces so that there are no health hazards for the employees. This also includes adequate lighting for individual visual tasks.

Within the scope of a risk assessment, it is necessary to determine and regularly check whether the workstations are suitably lit during operation. This can be resolved with a corresponding measuring device (lux meter).

Is daylight sufficient?

Daylight increases well-being, but in practice, it is not always sufficiently available at the right time or place. An additional artificial lighting system is, therefore, usually required. In our online shop, you will find many lighting systems, including wall and ceiling lights, tube lights, emergency lights, and flashlights. Many products are also available in ex-protected design.

Which lighting levels need to be observed?

"The same light for all" is not an adequate workplace solution. Because it depends on the individual visual task and how much light is needed in the workplace. A general lighting system ensures uniform illumination of the entire work area but does not consider the lighting requirements of individual room sections or workstations. Appendix 1 of the ASR A3.4 specifies the minimum values ​​to be observed for the illuminances and color reproduction indices for the different areas.

Table: Recommended lighting levels:

Workspaces, jobs and activities Lux Illuminance lx Colour rendering index Ra
Traffic areas and corridors without vehicle traffic 50 40
Traffic areas and corridors without vehicle traffic in the area of ​​paragraphs and steps 100 40
Traffic areas and corridors with vehicle traffic 150 40
Shipping and packaging areas 300 60
Storage rooms for identical or large-scale storage goods 50 60
Storage rooms with search for non-identical storage 100 60
Storage rooms with reading tasks 200 60
Colour test, control 1000 90
Laboratories, measuring stations 500 80
Trimming, finishing, control work in the chemical, plastics and rubber industries 750 80
Manufacture of tools and tools in metalworking and processing 750 60
Surface treatment and varnishing in metalworking and processing 750 80
Tool-, Gauging and device construction, precision and micromechanics in metalworking and processing 1000 80
Painting: Repair, inspection in the automotive industry 1000 90
Cable and wire production in the electrical industry 300 80
Impregnation of coils, electroplating in the electrical industry 300 80
Rough assembly work in the electrical industry, e.g. Large transformers 300 80
Medium-size assembly work in the electrical industry, e.g. Switchboard 500 80
Fine assembly work in the electrical industry, e.g. phones 750 80
Very fine assembly work in the electrical industry, e.g. measuring instruments 1000 80
Electronic workshops, testing, adjustment 1500 80
Quality control in woodworking and processing 1000 90

At no point in the workplace area may the temperature be 0.6 times lower than the average illuminance. The lowest value must not be within the range of the central vision task.

Suppose minimum illuminance levels of more than 500 lux are stipulated. In that case, they do not necessarily have to be achieved at the entire workplace but only at the partial surfaces relevant to the visual task. Partial lighting can be used, for example, when there is a unique visual task (working with small parts, short observation periods) or when adaptation to the individual's vision of the employees is necessary. Here, for example, the use of additional workplace lighting is recommended.

The following infographic illustrates the different lighting requirements in a workshop:

What do I need to know about installing and maintaining lighting systems?

It is advisable to plan and maintain lighting systems by a qualified person. After installing the lighting system and the necessary firing time, compliance with the legal requirements should be checked using control measurements.

Periodic testing and maintenance are also necessary to correct any changes in the lighting parameters, as well as to correct any contamination or damage.

What can I do to avoid glare?

To prevent glare, lighting should be selected to provide adequate visibility in work areas, but operating conditions must also be considered. It may also be helpful to reduce differences in brightness between the glare source and the environment (for example, due to bright ceilings and walls) and reflections due to matt surface design.

Lighting that offers a wide range of adjustment and positioning options is ideal here. In our online shop, you will find practical models for installation in the office, on drawing tables, or in workshops.

We are happy to help you!

You can get personalized guidance and service delivered right to you. Our sales reps are dedicated to meeting your needs with exceptional care—benefit from our range of service options, including phone, mail, or in-person assistance.

Professional guidance 1-877-388-0187

Related Content

Loading...
i

The specialist information on this page has been compiled carefully and to the best of our knowledge and belief. Nevertheless, DENIOS Inc cannot assume any warranty or liability of any kind, whether in contract, tort or otherwise, for the topicality, completeness and correctness either towards the reader or towards third parties. The use of the information and content for your own or third party purposes is therefore at your own risk. In any case, please observe the locally and currently applicable legislation.

Menu
Log in
Your basketAdded to basket
Go to basket
We would be pleased to provide you with advice!

Give us a call or fill out the form and we will get back to you as soon as possible.

Mon - Fri: 08:00 - 17:00